the cause of loss. In this sense, it is similar to first-party coverage. The term "no-fault" is most commonly used in the United States, Australia, and Canada...

Fault coverage refers to the percentage of some type of fault that can be detected during the test of any engineered system. High fault coverage is particularly...

A Byzantine fault is a condition of a system, particularly a distributed computing system, where a fault occurs such that different symptoms are presented...

"no-fault" coverage, because the statutes enacting it are generally known as no-fault laws, and PIP is designed to be paid without regard to "fault," or...

every possible stuck-at fault in a circuit. 100% stuck-at fault coverage does not necessarily guarantee high quality, since faults of many other kinds often...

pattern generation Fault coverage Single stuck line "Small-delay-defect testing" "OPTIMIZING TEST PATTERN GENERATION USING TOP-OFF ATPG" "Fault Modeling",[University...

critical data. In software testing, fault injection is a technique for improving the coverage of a test by introducing faults to test code paths; in particular...

are not subject to a fault rule (but may affect insurance rates and coverage depending on policyholder's claim history). The Fault Rules are for most every...

A stuck-at fault is a particular fault model used by fault simulators and automatic test pattern generation (ATPG) tools to mimic a manufacturing defect...

conceivable faults. It is used for refining both the test circuitry and the test patterns iteratively, until a satisfactory fault coverage is obtained...

this set of tests does not satisfy branch coverage since neither case will meet the if condition. Fault injection may be necessary to ensure that all...

the driver's share of responsibility, the identity of the at-fault driver, the coverage period and the reduction/increase coefficient at the anniversary...

to thoroughly test the functionality of a processor. Achieving good fault coverage requires immense engineering effort; even with all of the resources...

features. It often also makes it useful as a general verification tool, fault coverage, and performance analyser, especially if instruction path lengths are...

PBIT, CBIT, IBIT BIT Objectives: Fault detection, fault isolation, fault reporting Performance Requirements: Fault coverage Detection time Isolation capability...

receive high-quality coverage. Governments across the country have used various insurance schemes from full tort to full no-fault in pursuit of that goal...

Evaluation and acceptance procedures for polymeric adhesives 5012.1 Fault coverage measurement for digital microcircuits 5013 Wafer fabrication control...

retrofit flip-flops, wire scan chains, and generate test vectors with high fault coverage. Scan testing is especially critical in ASICs and SoCs, where internal...

where the other driver is not insured. This coverage applies only if the other party is found to be at fault for the incident. Depending on the state, the...

systematically generating tests targeting particular potential faults. This way the fault coverage can closely approach 100%, provided the design is properly...

Fault tree analysis (FTA) is a type of failure analysis in which an undesired state of a system is examined. This analysis method is mainly used in safety...

war has been extensively covered by media outlets around the world. This coverage has been diverse, spanning from traditional news outlets to social media...

approximately 10 mi (16 km) northeast of Santa Cruz on a section of the San Andreas Fault System and was named for the nearby Loma Prieta Peak in the Santa Cruz Mountains...

device is a complex digital device, with thousands of gates, then test fault coverage has to be calculated. Here again, the decision is complex based on test...

and compare them, and a statistical function determines whether or not a fault can be associated with any of the signals. RAIM is considered available...

a fault plane. The sides of a fault move past each other smoothly and aseismically only if there are no irregularities or asperities along the fault surface...

{\displaystyle Coverage={\frac {Faults\ Detected\ By\ CBM+Faults\ Detected\ By\ PMS}{Total\ Possible\ Faults}}} A rough estimate of coverage can be made...

covers damages from at-fault accidents and hit and runs. All Perils combines Comprehensive and Collision but adds some coverage. Each is optional to buy...

The Calaveras Fault is a major branch of the San Andreas Fault System that is located in northern California in the San Francisco Bay Area. Activity on...

limited tort coverage only apply in situations where the driver or passengers have been injured in an accident that is not the driver's fault. The victim...