A casting defect is an undesired irregularity in a metal casting process. Some defects can be tolerated while others can be repaired, otherwise they must...

After the shakeout of the casting it is inspected for defects. The most common defects are misruns and cold shuts. These defects can be caused by cold dies...

Sand casting, also known as sand molded casting, is a metal casting process characterized by using sand—known as casting sand—as the mold material. The...

Pulldown may refer to: Pulldown (casting), a type of casting defect Pull-down resistor, a type of resistor use Pull-down assay, a biochemical protein extraction...

a sheet like casting defect, produced by molten metal penetration into a sand casting mould. Veining a defect on the surface of a casting appearing as...

the casting process. The main types are: gas porosity, shrinkage defects, mold material defects, pouring metal defects, and metallurgical defects. Casting...

inventory due to theft, damage, spoilage, etc. Shrinkage defect or shrinkage void, a casting defect caused by metal solidifying from the outside inward Shrinkage...

place on an airport, depicted on airport diagrams Hot spot (casting), a metal casting defect Hot Spot (cricket), an infrared tracking system Airport hot...

Hydrogen gas porosity is an aluminium casting defect in the form of a porosity or void in an aluminium casting caused by a high level of hydrogen gas (H2)...

primarily involved in setting up peering exchanges Pipe (casting), a type of metal-casting defect Boatswain's pipe, an instrument used for signalling or...

An entrainment defect is a term used in metallurgy to describe a defect created in a casting by the folding-over of the oxidized surface layer of the...

Alumina can react with silica to form mullite. Veining (metallurgy), sand casting defect associated with the alpha to beta silica phase change "Ceramic Faults...

Steel-Slab Casting Mold and Defect Formation' - JOM Online". The Minerals, Metals, and Materials Society. Retrieved 2014-03-29. "'Analyzing Casting Problems...

patterns, and potential defects in the casting before the start of the actual production process. By simulating the casting process, manufacturers can...

Number. The presence of iron in aluminum helps in the decrease of casting defects, improves tensile, yield, hardness, and maintains strength at high...

Canada Blowhole Diversion Tunnel in Victoria, Australia A type of casting defect in metalworking Category:Blowholes This disambiguation page lists articles...

of minerals distinct from the surrounding rock Vein (metallurgy), a casting defect Vein (band), an American metalcore band Vein (Boris album), 2006 Vein...

to remove harmful gases and elements from the molten metal to avoid casting defects. Material is added during the melting process to bring the final chemistry...

should also be minimized because they can cause casting defects or create weak spots in the casting. It is usually more critical to ensure the upper...

Investment casting is an industrial process based on lost-wax casting, one of the oldest known metal-forming techniques. The term "lost-wax casting" can also...

of a rat Rattail, fish of the family Macrouridae Rattail (casting), a defect in metal casting Rattail (haircut) Rattail skate (Dipturus lanceorostratus)...

misadventures of the eponymous anthropomorphic dog Buckle (casting), a type of casting defect Buckle (clothing retailer) Buckle, a type of cobbler (food)...

high mechanical properties, reduced defects, and a fine microstructure. There are three steps in the ablation casting process: Mold preparation: A mold...

only happened because the previous drop had initiated a crack from a casting defect, that the crack would have been detected by inspection after the drop...

the material used was "high-grade". Similarly, casting was seen as high quality although casting defects were found in the side armour of the tank that...

Europe when locally made bells were available has also been noted. Casting defects were probably responsible for the 8 appearing as a 3. List of churches...

from sub-micron to voids greater than 10 mm, depending on the casting. Casting defects caused by porosity can affect the part’s structural integrity,...

Slip casting, or slipcasting, is a ceramic forming technique, and is widely used in industry and by craft potters to make ceramic forms. This technique...

in Weimar, Texas when the meter exploded, injuring one of the men. A casting defect in the meter was determined to be the cause of the explosion. May 17...

of accuracy, fine surface finish or defect free surface it reduces the castability of the part. However, the casting process can be very economical for...