An injection port is a medical device used for the administration of insulin or other physician-approved medicine into the subcutaneous tissue (the tissue...

types of manifold injection systems: multi-point (or port) and single-point (or throttle body) injection. Internal mixture formation systems can be separated...

injection: the multi-point injection (MPI) system, also known as port injection, or dry manifold system and the single-point injection (SPI) system, also known...

traditional syringes. Some people on an MDI regimen also use injection ports such as the I-port to minimize the number of daily skin punctures. The other...

Code injection is a computer security exploit where a program fails to correctly process external data, such as user input, causing it to interpret the...

deterrent. Dart injection Jet injector Injection port Lethal injection Needlestick injury Needle remover Safety syringe Trypanophobia "injection". Cambridge...

combining direct injectors with port (indirect) injectors, combining the benefits of both types of fuel injection. Direct injection allows the fuel to be precisely...

and an injection port for introducing the chemicals downstream of the check valve. Many chemigation valves also have a 4-inch inspection port so that...

Gasoline direct injection (GDI), also known as petrol direct injection (PDI), is a fuel injection system for internal combustion engines that run on gasoline...

use multi-port fuel injection, some have D4 direct injection, and others have a combination of direct injection and multi-port fuel injection or D4-S....

solution to prevent clotting, between uses of the catheter. Ported cannulae have an injection port on the top that is often used to administer medicine.: 349–354 ...

(the tissue layer located just beneath the skin). When applying the injection port, an insertion needle guides a soft cannula (a small, flexible tube)...

identification. However, the high temperatures (300°C) used in the GC–MS injection port (and oven) can result in thermal degradation of injected molecules,...

process of injection molding. They are best described as "off tone" wavy lines/streaks or patterns in the molded part around the injection ports. They commonly...

FP injection port was hidden under debris. The next morning (12 March, 04:00), approximately 12 hours after the loss of power, freshwater injection into...

after the injection port closes, and the piston is still rising, it is ignited in the compressed main charge of air. The use of direct injection and stratified...

An injection pump is the device that pumps fuel into the cylinders of a diesel engine. Traditionally, the injection pump was driven indirectly from the...

iteration that was launched in the 2009 model year included a third oil injection port in each rotor housing to feed oil to the middle of the rotor facing...

72 in × 2.63 in) with a compression ratio of 10.0:1 and electronic port injection. There are two versions of this engine, one for the Japanese domestic...

In computer science, fault injection is a testing technique for understanding how computing systems behave when stressed in unusual ways. This can be...

is typically located inside the fuel tank. For older port injection and throttle-body injection systems, this "in-tank" fuel pump transports the fuel...

manifold and/or uneven distribution of the nitrous/fuel mixture. Port and direct fuel injection engines have intake systems engineered for the delivery of air...

et al. (2011). "Directly suspended droplet microextraction with in injection-port derivatization coupled to gas chromatography–mass spectrometry for the...

or agitation. After extraction, the SPME fiber is transferred to the injection port of separating instruments, such as a gas chromatography and mass spectrometry...

the exhaust port, and direct injection effectively eliminates this problem. Two systems are in use: low-pressure air-assisted injection and high-pressure...

EcoBoost is a series of turbocharged, direct-injection gasoline engines produced by Ford and originally co-developed by FEV Inc. (now FEV North America...

culminating in fuel injection and ignition. Instead of a full set of valves, two-stroke diesel engines have simple intake ports, and exhaust ports (or exhaust...

In internal combustion engines, water injection, also known as anti-detonant injection (ADI), can spray water into the incoming air or fuel-air mixture...

detected. However, the high temperatures (300 °C) used in the GC-MS injection port (and oven) can result in thermal degradation of injected molecules,...

intake manifold to a DISA two-stage manifold, removal of secondary air injection ports and different heads to accommodate this change and the increased bore...