Reversing gear is a mechanism used to both control the direction of travel of a steam locomotive and adjust its engine's steam cutoff. The most common...

respectively, at the correct points in the cycle. It can also serve as a reversing gear. It is sometimes referred to as the "motion". In the simple case, this...

vehicle transmission system where gear changes require the driver to manually select the gears by operating a gear stick and clutch (which is usually...

gear", "high gear", and "reverse gear" refer to the overall torque ratios of different meshing configurations, rather than to specific physical gears...

A gear stick (rarely spelled gearstick), gear lever (both UK English), gearshift or shifter (both U.S. English), more formally known as a transmission...

reverse gear ratio, as electric motors can operate at a wider range of RPM, and provide their full torque even when close to 0 RPM. Reversing the motor...

of the manufacturer partly due to the absence of a dedicated reverse gear since reversing is provided by the electric motors mounted on the front axle...

Tegami Bachi: REVERSE, the second season of the Tegami Bachi anime series, 2010 Reverse gear, in a motor or mechanical transmission Reversing (vehicle maneuver)...

motor controlled the steam valves instead of the more common manual reversing gear. On the piston rod of a steam cylinder (the actual motor) a glycerine...

gear train or gear set is a machine element of a mechanical system formed by mounting two or more gears on a frame such that the teeth of the gears engage...

appropriate reverse gear R1, the input (turbine) is put through gearset 1 first. This reduction corresponds to the ratio of the 3rd gear. Therefore, the gear step...

pressed). Reverse (R): This position engages reverse gear, so that the vehicle drives in a backwards direction. It also operates the reversing lights and...

transmission. It has 2 reverse gears. The transmission can skip gears when downshifting. It also has a torque converter lock-up on all 7 gears, allowing better...

operated automatically by a single reversing lever. One was actuated by a bellcrank, the other through a reversing linkage from this, so that as one engaged...

as the smallest production car ever made. The original model has no reverse gear, but a handle at the rear allows the very lightweight car to be maneuvered...

epicyclic gear train (also known as a planetary gearset) is a gear reduction assembly consisting of two gears mounted so that the center of one gear (the "planet")...

drive with direct-reversing engines. While an FPP-equipped vessel needs either a reversing gear or a reversible engine to reverse, a CPP vessel may not...

Reverser may refer to: Thrust reverser Reversing gear, often called a reverser, controls the valves on a steam engine Reverser handle, an operating lever...

of the placement of the gears with relation to neutral, though some motorcycle gearboxes and/or shift mechanisms can be reversed so that a "one up, four...

longitudinal engine configurations, the series includes 4 forward gears and 1 reverse gear. The 4L60E is the electronically commanded evolution of the Turbo-Hydramatic...

as a "railroad key." A reversing mechanism of some type has been present on locomotives almost since inception. The reversing lever on a steam locomotive...

with petrol/CNG M111 engine, Jeep Wrangler, etc.). plus 2 reverse gears Differences in gear ratios have a measurable, direct impact on vehicle dynamics...

younger Drummond's locomotives was complete, was the provision of a reversing gear, a troublesome mechanism if it were not well maintained. With the introduction...

longer) Ratios: First Gear: 3.830:1 Second Gear: 2.062:1 Third Gear: 1.436:1 Fourth Gear: 1.00:1 Fifth Gear: 0.838:1 Reverse Gear 4.22:1 A 4WD manual transmission...

valve is closed. On a steam locomotive, the cutoff is controlled by the reversing gear. The point at which the inlet valve closes and stops the entry of steam...

railway vehicle, it sometimes incorporates the reversing gear. Examples include the Self-Changing Gears RF 28 (used in many first-generation diesel multiple...

off). Reversing An intermediate gear which does not drive a shaft to perform any work is called an idler gear. Sometimes, a single idler gear is used...

reach rod that connected it to the reversing lever. This not only simplified reversing but it was realised that the gear could be raised or lowered in small...

additional direction gear was kept, which means that all 24 gears can also be used in reverse mode. Since the highest final gear ratio allows top speeds...

for gear 1 to 4 and reverse gear · supplemental housing for gear 5 hydraulic for gear 1 to 4 and reverse gear · electronic for gear 5 3 simple planetary...