The circuit topology of an electronic circuit is the form taken by the network of interconnections of the circuit components. Different specific values...

The circuit topology of a folded linear polymer refers to the arrangement of its intra-molecular contacts. Examples of linear polymers with intra-molecular...

consisting of electrical elements (e.g., voltage sources, current sources, resistances, inductances, capacitances). An electrical circuit is a network...

Electronic filter topology defines electronic filter circuits without taking note of the values of the components used but only the manner in which those...

An RLC circuit is an electrical circuit consisting of a resistor (R), an inductor (L), and a capacitor (C), connected in series or in parallel. The name...

in a series or parallel topology. Whether a two-terminal "object" is an electrical component (e.g. a resistor) or an electrical network (e.g. resistors...

Network topology is the arrangement of the elements (links, nodes, etc.) of a communication network. Network topology can be used to define or describe...

electrical phenomena. Electrical systems are commonly described by means of a circuit diagram. These are network diagrams that describe the topology of...

Electrical resonance occurs in an electric circuit at a particular resonant frequency when the impedances or admittances of circuit elements cancel each...

together. The circuit can act as an electrical resonator, an electrical analogue of a tuning fork, storing energy oscillating at the circuit's resonant frequency...

Topology (from the Greek words τόπος, 'place, location', and λόγος, 'study') is the branch of mathematics concerned with the properties of a geometric...

electrical current in a circuit. It is typically used to divert current away from a system or component in order to prevent overcurrent. Electrical shunts...

An electrical ballast is a device placed in series with a load to limit the amount of current in an electrical circuit. A familiar and widely used example...

In electrical and electronic engineering, a daisy chain is a wiring scheme in which multiple devices are wired together in sequence or in a ring, similar...

lumped-element model simplifies the system or circuit behavior description into a topology. It is useful in electrical systems (including electronics), mechanical...

A bridge circuit is a topology of electrical circuitry in which two circuit branches (usually in parallel with each other) are "bridged" by a third branch...

Electronic filters are a type of signal processing filter in the form of electrical circuits. This article covers those filters consisting of lumped electronic...

transformer circuit topology (i.e., both ports independently excited with no short-circuited port). The dual ported transformer circuit topology is known...

inverters are primarily used in electrical power applications where high currents and voltages are present; circuits that perform the same function for...

simulator, with subcircuit models that use the actual transistor topology of the integrated circuit, and finally, with inline Boolean logic expressions. Exact...

In electrical circuit theory, a port is a pair of terminals connecting an electrical network or circuit to an external circuit, as a point of entry or...

unchanged. Mesh analysis Ohm's law Kirchhoff's circuit laws Circuit diagram Circuit topology (electrical) Ybus matrix Charge conservation P. Dimo Nodal...

stage. Switched-mode power supplies can be classified according to the circuit topology. The most important distinction is between isolated converters and...

a bridge circuit, it is impossible to simultaneously ground the input and output of this circuit. The Delon circuit uses a bridge topology for voltage...

ratings. Diodes are also used in bridge topologies along with capacitors as voltage multipliers. The diode bridge circuit was invented by Karol Pollak and patented...

temperature range of 100 °C. For this reason, in 2001, Malcovati designed a circuit topology that can compensate high-order non-linearities, thus achieving an improved...

A resistor–inductor circuit (RL circuit), or RL filter or RL network, is an electric circuit composed of resistors and inductors driven by a voltage or...

in 1983, defining the electrical characteristics of drivers and receivers for use in serial communications systems. Electrical signaling is balanced,...

affected circuit elements to withstand high current or voltage spikes due to fast voltage changes; dV/dt is usually expressed in V/microsecond. A topology is...

In electronics, a split-pi topology is a pattern of component interconnections used in a kind of power converter that can theoretically produce an arbitrary...